bei mir erstellt gerade ein e2-Image und wollte mal wissen was passiert wenn ich fertig bin?
Das ist ein wichtiges Thema.
X
X
-
Wollte mir heute auch mal ein E2 erstellen. Leider wird der Durchlauf mit dieser Meldung abgebrochen.
Einer ne Idee was das sein könnte:
+ test -f /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-target-glibc-2.5-27.i386/tdt/tdt/tufsbox/cdkroot/usr/share/info/libc.info-10
+ gzip -9 -f /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-target-glibc-2.5-27.i386/tdt/tdt/tufsbox/cdkroot/usr/share/info/libc.info-10
+ test -L /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-target-glibc-2.5-27.i386/tdt/tdt/tufsbox/cdkroot/usr/share/info/libc.info-10
+ read AFile
Fehler: Fehler-Status beim Beenden von /var/tmp/rpm-tmp.33924 (%install)
Fehler beim Bauen des RPM:
Fehler-Status beim Beenden von /var/tmp/rpm-tmp.33924 (%install)
make: *** [RPMS/sh4/stlinux22-sh4-glibc-2.5-27.sh4.rpm] Fehler 1
Edit: Vielleicht hat er irgend ne Datei nicht richtig runter geladen?
Wie kann ich denn alles ganz neu anstoßen?
So dass alles neu geladen wird?
Hab nochmal alles gelöscht und neugemacht. Jetzt kommt aber immer:
tufsbox/host/bin/
mkdir -p /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-host-base-passwd-3.5.9-3.i386/tdt/tdt/tufsbox/host/man/man8
/usr/bin/install -c -m 644 ../man/update-passwd.8 /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-host-base-passwd-3.5.9-3.i386/tdt/tdt/tufsbox/host/man/man8/
make[1]: Verlasse Verzeichnis '/tdt/tdt/cvs/cdk/BUILD/base-passwd/objdir'
+ cd ..
+ find /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-host-base-passwd-3.5.9-3.i386/tdt/tdt/tufsbox/host/man '(' '(' -type f -o -type l ')' -a '!' -name '*.gz' ')' -print
+ read AFile
+ test -f /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-host-base-passwd-3.5.9-3.i386/tdt/tdt/tufsbox/host/man/man8/update-passwd.8
+ gzip -9 -f /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-host-base-passwd-3.5.9-3.i386/tdt/tdt/tufsbox/host/man/man8/update-passwd.8
+ test -L /tdt/tdt/cvs/cdk/BUILDROOT/stlinux22-host-base-passwd-3.5.9-3.i386/tdt/tdt/tufsbox/host/man/man8/update-passwd.8
+ read AFile
Fehler: Fehler-Status beim Beenden von /var/tmp/rpm-tmp.42631 (%install)
Fehler beim Bauen des RPM:
Fehler-Status beim Beenden von /var/tmp/rpm-tmp.42631 (%install)
make: *** [RPMS/sh4/stlinux22-host-base-passwd-3.5.9-3.sh4.rpm] Fehler 1
__________________
Atevio7500: titan, WLAN Fritzbox 7270
TV: LED Samsung. Zweitbox: UFS910, NAS: Ubuntu 12.04 Server 3TB, Zotac mag mini
Kommentar
-
Original von MichaelAnders
Original von rico-one
bei mir erstellt gerade ein e2-Image und wollte mal wissen was passiert wenn ich fertig bin?
Hatte dann auch leider keine Zeit, der Sache nachzugehen, weil mein Hausdrache die Kathi für sich haben wollte
Kommentar
-
Original von ckiter
Original von MichaelAnders
Ich habs auch ins MINI1 gepackt - siehe hier.Dreambox 8000S
Kathi UFS 912 / 910
Kommentar
-
komisch. rev 54 baut bei mir das e²-nightly nicht mehr. bricht mit nem openrdate fehler ab.
werde auch selbst nach löschen des kompletten git nichtmehr gefragt, ob ich 2a bauen will oder ein anderes. sehr seltsam.-= Kathi 910 =-
13°, 19.2°, 23.5°, 28,2° @ Moteck SG-2100A Rotor
Smargo SmartReader Plus
-= =-
Kommentar
-
Original von officiallyme
komisch. rev 54 baut bei mir das e²-nightly nicht mehr. bricht mit nem openrdate fehler ab.
werde auch selbst nach löschen des kompletten git nichtmehr gefragt, ob ich 2a bauen will oder ein anderes. sehr seltsam.
Grüße
Kommentar
-
hi folks,
hab mal ne frage...
wenn ich settings ins selbst gebaute e2 übernehmen will, kommen die doch nach /etc/enigma2, oder ?
komischerweise funzt das bei mir nicht. bei den aaf images kann ich settings/bouquets hin- und herkopieren wie ich möchte. liegt es am skin ?
bin da ein wenig hilflos.....
greetz
Lanzelot
Kommentar
-
welches enigma2 hast du denn gebaut? nightly oder nicht-nightly?
je nachdem sind die pfade ja unterschiedlich. wenn ich nicht irre, ist das stable nämlich vom märz und da waren die settings noch in usr/local/share/enigma2/
kann mich aber irren. am besten mal in dein tar reinschauen, wo die aktuellen bouquets liegen.
und dran denken, dass die satellites.xml eventuell an mehr als einem ort liegt. hab noch nicht geschaut, ob die symlinks alle passen.-= Kathi 910 =-
13°, 19.2°, 23.5°, 28,2° @ Moteck SG-2100A Rotor
Smargo SmartReader Plus
-= =-
Kommentar
-
Original von officiallyme
welches enigma2 hast du denn gebaut? nightly oder nicht-nightly?
je nachdem sind die pfade ja unterschiedlich. wenn ich nicht irre, ist das stable nämlich vom märz und da waren die settings noch in usr/local/share/enigma2/
kann mich aber irren. am besten mal in dein tar reinschauen, wo die aktuellen bouquets liegen.
und dran denken, dass die satellites.xml eventuell an mehr als einem ort liegt. hab noch nicht geschaut, ob die symlinks alle passen.
jemand ne idee ?
ansonsten lüppt das image richtig gut. habe die devices in der /etc/fstab gemountet und einen stick mit einer Swappartition genommen. enorm stabil auch bei timeshift....
greetz
Lanzelot
Kommentar
-
@Was muss ich den für die CubeRevo eingeben ? Läuft das unter Topfield ?
das Original-Zitat, aus dem kathi-forum von pinky1981:
@
git +cuberevo (viz)
make.sh
##############################################
echo "Targets:"
echo "1) Kathrein UFS-910"
echo "2) Kathrein UFS-922"
echo "3) Topfield 7700 HDPVR"
echo "4) HDBox"
echo "5) Cuberevo/Vizyon"
read -p "Select target (1-5)? "
[ "$REPLY" == "1" ] && CONFIGPARAM="$CONFIGPARAM --enable-ufs910"
[ "$REPLY" == "2" ] && CONFIGPARAM="$CONFIGPARAM --enable-ufs922"
[ "$REPLY" == "3" ] && CONFIGPARAM="$CONFIGPARAM --enable-tf7700"
[ "$REPLY" == "4" ] && CONFIGPARAM="$CONFIGPARAM --enable-fortis_hdbox"
[ "$REPLY" == "5" ] && CONFIGPARAM="$CONFIGPARAM --enable-cuberevo"
[ "$REPLY" == "1" -o "$REPLY" == "2" -o "$REPLY" == "3" -o "$REPLY" == "4" -o "$REPLY" == "5" ] || CONFIGPARAM="$CONFIGPARAM --enable-ufs910"
##############################################
read -p "Building for stm23(instable) instead of stm22(stable) (y/N)? "
[ "$REPLY" == "y" -o "$REPLY" == "Y" ] && CONFIGPARAM="$CONFIGPARAM --enable-stm23"
[ "$REPLY" == "y" -o "$REPLY" == "Y" ] || CONFIGPARAM="$CONFIGPARAM --enable-stm22 --enable-p0041"
##############################################
vllt kann des ja ma jemand testen der ne viz/cuberevo hat. zumindest stehts so im confugre.ac mit drin zwinkern
rest wird ja in den .mk mittels strings abgefragt ob cube or not
@
Kommentar
-
Hallo ,
git pull gibt mir nen Fehler aus :
Permission denied (publickey).
fatal: The remote end hung up unexpectedly
was ist da los liegt das an mir ?
Also hab ich mir auch mal die configure.ac angeschaut und siehe da es sind noch mehr Boxen drin
hab mal die make.sh für mich angepasst ,weil ich ne ip910 habe :
##############################################
echo "Targets:"
echo "1) Kathrein UFS-910"
echo "2) Kathrein UFS-922"
echo "3) Topfield 7700 HDPVR"
echo "4) HDBox"
echo "5) Cuberevo/Vizyon"
echo "6) Cuberevo-mini/900hd"
echo "7) Cuberevo-mini2/910hd"
read -p "Select target (1-7)? "
[ "$REPLY" == "1" ] && CONFIGPARAM="$CONFIGPARAM --enable-ufs910"
[ "$REPLY" == "2" ] && CONFIGPARAM="$CONFIGPARAM --enable-ufs922"
[ "$REPLY" == "3" ] && CONFIGPARAM="$CONFIGPARAM --enable-tf7700"
[ "$REPLY" == "4" ] && CONFIGPARAM="$CONFIGPARAM --enable-fortis_hdbox"
[ "$REPLY" == "5" ] && CONFIGPARAM="$CONFIGPARAM --enable-cuberevo"
[ "$REPLY" == "6" ] && CONFIGPARAM="$CONFIGPARAM --enable-cuberevo_mini"
[ "$REPLY" == "7" ] && CONFIGPARAM="$CONFIGPARAM --enable-cuberevo_mini2"
[ "$REPLY" == "1" -o "$REPLY" == "2" -o "$REPLY" == "3" -o "$REPLY" == "4" -o "$REPLY" == "5" -o "$REPLY" == "6" -o "$REPLY" == "7" ] || CONFIGPARAM="$CONFIGPARAM --enable-ufs910"
##############################################
führe die make.sh aus :
Targets:
1) Kathrein UFS-910
2) Kathrein UFS-922
3) Topfield 7700 HDPVR
4) HDBox
5) Cuberevo/Vizyon
6) Cuberevo-mini/900hd
7) Cuberevo-mini2/910hd
Select target (1-7)? 7
Building for stm23(instable) instead of stm22(stable) (y/N)?
... bla bla..
und nach dem confiugure zeigt er mir auch an:
cuberevo mini 2 stuff: yes
und den Build angeschoben :
make: *** Keine Regel vorhanden, um das Target »Patches/cuberevo_patches_p0041.patch«,
benötigt von ».deps/linux-kernel.do_prepare«, zu erstellen. Schluss.
Kommentar
Nicht konfiguriertes PHP-Modul
Einklappen
Anleitung e2 Image erstellen
Einklappen
Kommentar