X

Box wiederbeleben?

Einklappen
 
  • Filter
  • Zeit
  • Anzeigen
Alles löschen
neue Beiträge
  • travego81
    Erfahrene Benutzer
    • 30.12.2007
    • 149

    Box wiederbeleben?

    Hallo, habe folgendes Problem mit meiner 510HD: Habe Update auf 1.87 gemacht, die Box lief kurze Zeit, meckerte aber beim Start immer wieder mal rum, das Swap neu erstellt wird.
    Später fing es an, das sie öfters beim Boot Vorgang hängen blieb.
    Ich habe darauf hin versucht mit der Ch+ Taste das Image neu zu flashen, aber das ging nicht mehr, die Box startete immer bis Booting, dann Ende. Dann hätte ich versucht aktuellen Bootloader drauf zu schieben, mit Menü Taste beim Einschalten, das ging gar nicht. Nun hab ich seit gestern die Box in Ruhe gelassen und heute als ich Einschalten wollte bekam ich nicht mal mehr ein Bild vom Bootloader, sie blinkt zuerst rot/grün und nach ca. halben Minute bleibt die LED dauerhaft grün. Kann ich irgendwie wie damals bei der Kathi910 ein Notfalltool über serielle Schnittstelle versuchen um das ganze wieder zu recovern? Hätte schon mit Putty unter Windows10 versucht beim Start was auszulesen, weiß nur nicht ob ich alles richtig konfiguriert habe, da ich keine Ausgabe bekam. Kann jemand helfen?
  • Uljanow
    Super-Moderator
    • 01.01.2008
    • 16911

    #2
    Kommst du ins iBoot-Menü? (Beim Box einschalten sofort mehrmals die Menütaste an der Fernbedienung drücken).
    sigpic
    Lebe jeden Tag so als wäre es Dein Letzter!

    Kommentar

    • ciccio81
      Erfahrene Benutzer
      • 28.08.2009
      • 144

      #3
      hänge mich ihr gleich mit meine 510er startet auch nicht bekomm diese meldung

      i-boot timepoint 1432 ms executing bootcmd_x

      ## Booting kernel from Legacy Image at 81801000 ...
      Image Name: Linux-2.6.32.59_stm24_0211
      Image Type: SuperH Linux Kernel Image (gzip compressed)
      Data Size: 1910836 Bytes = 1.8 MiB
      Load Address: 80801000
      Entry Point: 80802000
      Verifying Checksum ... OK
      Uncompressing Kernel Image ... OK

      Starting kernel:
      start = 0x80802000
      initrd = 0x00000000 (0 bytes)
      bootargs = console=ttyAS0,115200 root=/dev/mtdblock3 rootfstype=squashfs ip=::::sdk:eth0ff nwhwconf=device:eth0,hwaddr:00:1E:B8:06:AD:11 bigphysarea=5000 stb7111:eth0ff stmmaceth=msglvl:0,watchdog:4000,rxsize:16 mtdparts=physmap-flash:384K(Boot_firmware),2688k@0x60000(kernel),0K @0x1060000(App),13696k@0x300000(ROOT_FS),0K@0x1060 000(Device),1M@0x1b00000(CONFIG),4M@0x01c00000(Use r),32M@0(All),0K@0x1060000(APP_ORG),0K@0x1060000(A PP_BAK) loglevel=8


      i-boot needed 2476 ms to start the kernel


      da bleibt se stehen u geht net weiter

      Kommentar

      • Uljanow
        Super-Moderator
        • 01.01.2008
        • 16911

        #4
        Sieht soweit gut aus. Was geht denn nicht? Kommst du in das iBoot-Menü rein?
        sigpic
        Lebe jeden Tag so als wäre es Dein Letzter!

        Kommentar

        • ciccio81
          Erfahrene Benutzer
          • 28.08.2009
          • 144

          #5
          ja hab mehr mal flash formatiert u image installert nur die box startet nicht hab sogar ältere img versucht

          Kommentar

          • Uljanow
            Super-Moderator
            • 01.01.2008
            • 16911

            #6
            Da hilft sicher nur noch ein serielles Log um zu sehen wo es hängt.
            sigpic
            Lebe jeden Tag so als wäre es Dein Letzter!

            Kommentar

            • ciccio81
              Erfahrene Benutzer
              • 28.08.2009
              • 144

              #7
              das war mein serieller log

              Kommentar

              • andy-1
                Administrator
                • 08.06.2007
                • 40627

                #8
                Unterkategorien

                4.6.2 MENU-FLASH (zurück)
                • 1.USB IRDupdt Image flash per Usb-Stick oder Usb-HDD von sda1 (standard) (abhängig von SETTINGS>Select USB/SATA dev 1-4)

                • 2.list USBirds wenn mehrere ird Image's auf dem Usb-Stick liegen, kann man sich diese anzeigen lassen und dann das Richtige flashen

                • 3.clean environment sector setzt die Bootargs zurück und bringt I-boot in den Standard Modus, wenn man keinen Experten Modus nutzen will wegen der Garantie

                • 4. clean Flash ! Include swap löscht das komplette Image, inklusive den Swap-Bereich, also alle Einstellungen, Plugins, Backups und so weiter.

                • 5. SATA IRDupdt hiermit kann man ein ird Image von einer internen Platte oder einer extern SATA/e-SATA Platte flashen

                • 6. list SATAirds wenn mehre ird Image's auf dem SATA/e-SATA liegen, kann man sich diese anzeigen lassen und dann das Richtige flashen

                • 7. allow I-boot update Entwickler Option damit man auch nur das image flashen kann und der auf der Box befindliche Bootloader nicht überschrieben wird
                Einstellungsoptionen:
                0 - i-boot darf nicht überschrieben werden
                1 - i-boot darf überschrieben werden (Standardeinstellung)

                Der Bootloader steht auf überschreiben und standard environment sector (Bootargs) ?

                Kommentar

                • ciccio81
                  Erfahrene Benutzer
                  • 28.08.2009
                  • 144

                  #9
                  1 bis 6 alles versucht teste mal punkt 7

                  Kommentar

                  • andy-1
                    Administrator
                    • 08.06.2007
                    • 40627

                    #10
                    aktuelles Image dann

                    Kommentar

                    • ciccio81
                      Erfahrene Benutzer
                      • 28.08.2009
                      • 144

                      #11
                      das ist das ergebniss


                      o
                      // Boot
                      // interactive
                      // by (c) SoLaLa
                      ^^^ new OSD EHCI beta

                      U-Boot 2010.03-svn38337 - stm24_0122
                      (Aug 25 2016 - 10:54:4


                      Board: STx7111-HDK
                      32-bit 450 MHz
                      DRAM: 256 MiB
                      NOR: 32 MiB
                      In: serial
                      Out: serial
                      Err: serial

                      i-boot timepoint 252 ms before frontpanel init

                      done, AM510, cpuid 2D43B041

                      i-boot timepoint 312 ms main loop entered
                      Hit any key to stop autoboot: 0
                      CPU clock=650
                      add entry:0 - ---FLASH---
                      entering bootmenu - default:0 - ---FLASH--- timeout 2000
                      ---FLASH---CPU clock=450
                      (Re)start USB...
                      USB: STM EHCI HCD initialization HCCR=0xfe1ffe00, HCOR=0xfe1ffe10, hc_length=16
                      Register 1111 NbrPorts 1
                      USB EHCI 1.00
                      scanning usb bus for devices... 2 USB Device(s) found
                      scanning bus for storage devices... 1 Storage Device(s) found
                      system volume information/
                      151708 m40968_atemio510_v1-87_nightly_bootloaderusb_g250.ird

                      1 file(s), 1 dir(s)

                      IRDimages found in Directory:
                      1 m40968_atemio510_v1-87_nightly_bootloaderusb_g250.ird
                      reading m40968_atemio510_v1-87_nightly_bootloaderusb_g250.ird
                      .

                      151708 bytes read
                      filesize 2509c loadaddr 80000000
                      processing fup: irdbuffer 80000000 endofbuffer 8002509c
                      -> header
                      fpversion 0010 systemId: 252902A0 blockcount: 0008
                      softwareVersion: 00020961
                      parttype 0 found in .ird ...
                      ird examination ok, MTDsizes 256k 0k 0k 0k 0k 0k

                      returned success from ird processing with endpoint 2509c
                      mtdparts=physmap-flash:384K(Boot_firmware),0k@0x60000(kernel),0K@0x 60000(App),0k@0x60000(ROOT_FS),0K@0x60000(Device), 1M@0x1b00000(CONFIG),4M@0x01c00000(User),32M@0(All ),0K@0x60000(APP_ORG),0K@0x60000(APP_BAK)
                      Unprotecting Flash...
                      Erasing Flash...
                      . done
                      Erased 1 sectors
                      Writing to Flash...
                      done
                      Protecting Flash...
                      going to copy data
                      -> header
                      fpversion 0010 systemId: 252902A0 blockcount: 0008
                      softwareVersion: 00020961

                      erasing Part idx 0
                      erasepart 0
                      protect off A0000000 A003FFFF
                      erase A0000000 A003FFFF

                      .. done
                      Erased 2 sectors

                      returned from flashing with endpoint 2509c
                      ok

                      i-boot timepoint 160 ms



                      o
                      // Boot
                      // interactive
                      // by (c) SoLaLa
                      ^^^ new OSD EHCI beta

                      U-Boot 2010.03-svn38337 - stm24_0122
                      (Aug 25 2016 - 10:54:4


                      Board: STx7111-HDK
                      32-bit 450 MHz
                      DRAM: 256 MiB
                      NOR: 32 MiB
                      In: serial
                      Out: serial
                      Err: serial

                      i-boot timepoint 252 ms before frontpanel init

                      done, AM510, cpuid 2D43B041

                      i-boot timepoint 312 ms main loop entered
                      Hit any key to stop autoboot: 0
                      CPU clock=650
                      add entry:0 - ---FLASH---
                      entering bootmenu - default:0 - ---FLASH--- timeout 2000
                      ---FLASH---
                      selection done by timeout

                      i-boot timepoint 2448 ms executing bootcmd_x

                      ## Booting kernel from Legacy Image at 81801000 ...
                      Image Name: Linux-2.6.32.59_stm24_0211
                      Image Type: SuperH Linux Kernel Image (gzip compressed)
                      Data Size: 1910706 Bytes = 1.8 MiB
                      Load Address: 80801000
                      Entry Point: 80802000
                      Verifying Checksum ... OK
                      Uncompressing Kernel Image ... OK

                      Starting kernel:
                      start = 0x80802000
                      initrd = 0x00000000 (0 bytes)
                      bootargs = console=ttyAS0,115200 root=/dev/mtdblock3 rootfstype=squashfs ip=::::sdk:eth0ff nwhwconf=device:eth0,hwaddr:00:1E:B8:06:AD:11 bigphysarea=5000 stb7111:eth0ff stmmaceth=msglvl:0,watchdog:4000,rxsize:16 mtdparts=physmap-flash:384K(Boot_firmware),2688k@0x60000(kernel),0K @0x1060000(App),13696k@0x300000(ROOT_FS),0K@0x1060 000(Device),1M@0x1b00000(CONFIG),4M@0x01c00000(Use r),32M@0(All),0K@0x1060000(APP_ORG),0K@0x1060000(A PP_BAK) loglevel=8

                      Kommentar

                      • andy-1
                        Administrator
                        • 08.06.2007
                        • 40627

                        #12
                        stable auch schon probiert ?

                        Kommentar

                        • ciccio81
                          Erfahrene Benutzer
                          • 28.08.2009
                          • 144

                          #13
                          hab das stable 1.86 , letzte nigtly letzte stable .

                          werd versuchen mal die original von fortis testen.

                          Kommentar

                          • ciccio81
                            Erfahrene Benutzer
                            • 28.08.2009
                            • 144

                            #14
                            so nach fortis install bekomm ich diesen log

                            %)▒▒FrTs........................................Fr Ts
                            init started: BusyBox v1.14.2 (2012-03-12 15:08:37 KST)
                            root::0:0:root:/tmp:/bin/sh
                            Starting app: ##### Get System Information OK! #####
                            ///////////////////////////////
                            STFAE_Init......
                            ///////////////////////////////
                            STFAE_Init 1
                            STFAE_Init 5
                            STFAE_Init 6
                            STFAE_Init 7
                            STFAE_Init 14
                            STFAE_Init 15
                            STFAE_Init 16
                            STFAE_Init 17
                            STFAE_Init 18
                            STFAE_Init 19
                            STFAE_Init 20
                            STFAE_Init 21
                            STFAE_Init 23
                            STFAE_Init 24
                            STFAE_Init 25
                            STFAE_Init 26
                            STFAE_Init 27
                            STFAE_Init 28
                            STFAE_Init 29
                            STFAE_Init 32
                            STFAE_Init 32
                            STFAE_Init 33
                            STFAE_Init 34
                            STFAE_Init 35
                            STFAE_Init 36
                            STFAE_Init 37
                            STFAE_Init 38

                            VOUT_FindI2cNumForHDMI 2

                            STFAE_Init 42
                            ================================================== ===========================
                            SECTOOLFUSE_Setup(SECTOOLFUSE_00)================= ================================================== ===========
                            - TKDMA_Init() Failure<0x15a0001>!!!
                            STFAE_Init OK
                            Front_IrInit : et6202_fd(ffffffff)
                            fd_front 30
                            # VFD type : 10002, ver : 1
                            _micom_type : 65538
                            ..... [WiA8293_IicInit] error 0
                            DVB-CI mode 1 disable
                            ..... pes start [0][0], buffer 0
                            ..... pes start [0][0], signal 0
                            ..... pes start [1][0], buffer 0
                            ..... pes start [1][0], signal 0
                            ..... pes start [0][1], buffer 0
                            ..... pes start [0][1], signal 0
                            ..... pes start [1][1], buffer 0
                            ..... pes start [1][1], signal 0
                            ============================================
                            ====== Start Main Application =============
                            ============================================
                            Init Wi OK
                            ### CI PLUS CERTIFICATE DATA BROKEN!####
                            ### CI PLUS CERTIFICATE DATA BROKEN!####
                            ### CI PLUS CERTIFICATE DATA BROKEN!####
                            DVB-CI mode 1 disable
                            DVB-CI mode 1 disable

                            Kommentar

                            • Uljanow
                              Super-Moderator
                              • 01.01.2008
                              • 16911

                              #15
                              Hast du ein CI-Modul stecken?
                              sigpic
                              Lebe jeden Tag so als wäre es Dein Letzter!

                              Kommentar

                              Nicht konfiguriertes PHP-Modul

                              Einklappen

                              Box wiederbeleben?

                              Einklappen
                              Lädt...
                              X